Abstract
A bellows-cup vacuum gripping tool comprising one tool-change interface, one bellows cup, one vacuum pump, one contact detector and one blow-off valve. When the bellows cup reaches the workpiece, the bellows cup is evacuated by the vacuum pump. After the workpiece has reached the set-down position, the workpiece is blown off by the blow-off valve. The arrangement is a proposed configuration composed from a typed library of mechanism blocks derived from published patents; it has not been constructed.
1. Purpose and arrangement
[0001]This disclosure describes a bellows-cup vacuum gripping tool: one bellows cup carried on a tool-change interface, fed by a vacuum pump. It is arranged for starting the cycle at the moment of contact, clearing the face at release, taking up height differences at the face and exchanging the tool without rewiring the cell. One concrete embodiment is described; every connection is stated with the medium it carries, and the operating sequence is given as conditions on named operations.
2. Components, construction and connections
[0002]One tool-change interface. The tool-change interface splits the tool into a robot side and a tool side, so the tool can be exchanged without dismantling it. The tool-change interface has a mechanical lock.
[0003]One bellows cup. Each bellows cup is folded so that it shortens under vacuum and takes up a height difference between the face and the workpiece. Each bellows cup has three folds.
[0004]One vacuum pump. The pump draws the circuit down mechanically and adds its own mass to the moving assembly.
[0005]One contact detector. The contact detector reports the moment a workpiece is present at the gripping face; its sensing technology is not fixed by this arrangement. The contact detector is mounted on the frame.
[0006]One blow-off valve. The blow-off valve drives compressed air back through the circuit to the face, which clears the face instead of waiting for the circuit to refill. The blow-off is a short pulse. The blow-off pulse is given after set-down.
[0007]The bellows cup is carried on the tool side of the tool-change interface.
[0008]The vacuum pump is fixed to the tool side of the tool-change interface.
[0009]The bellows cup is connected to the pump inlet line by a single vacuum line, so that the face is evacuated through that line.
[0010]The contact detector is mounted on the frame and reports the moment a workpiece is present against the gripping face.
[0011]The blow-off valve is connected to the circuit at the pump inlet line, so that compressed air can be driven back through the circuit to the face.
[0012]The robot side of the tool-change interface is bolted to the robot flange.
[0013]The pump motor is supplied from the electrical supply of the cell.
[0014]The blow-off valve is fed from the compressed air supply of the cell.
[0015]The blow-off valve is switched by the cell controller; the contact detector reports to the cell controller.
3. Operating sequence and conditions
[0016]
- After the contact detector has detected the workpiece, the vacuum supply is actuated by the cell controller.
[0017]
- When the bellows cup reaches the workpiece, the bellows cup is evacuated by the vacuum pump.
[0018]
- After the workpiece has reached the set-down position, the workpiece is blown off by the blow-off valve.
[0019]
- The workpiece is held until the blow-off valve has opened the circuit.
[0020]The cell controller reads the contact detector (on the frame) and commands the blow-off valve; no sensor drives an actuator directly.
4. Parameters and operating assumptions
[0021]Parameter values of this embodiment: locking of the tool-change interface: mechanical (sets what has to be present at the interface for the tool to stay attached); folds of the bellows cup: three (sets the travel taken up between the face and the workpiece, and the lateral stiffness of the cup under load); material of the bellows cup: plastic (sets the friction at the lip and the resistance of the folds to fatigue); drive medium of the vacuum pump: electric (sets the supply the pump motor needs from the cell); placement of the contact detector: on the frame (sets where the presence of the workpiece is detected); duration of the blow-off valve: a short pulse (sets how quickly the face clears and how much air each release costs); timing of the blow-off valve: after set-down (sets whether the pulse assists a drop release or clears the face after set-down).
[0022]The blow-off is a short pulse: the valve opens for a fraction of a second, long enough to break the seal and clear the face, and closes again.
[0023]The lock is engaged by a manually operated lever on the interface; no supply crosses the interface for the lock, and tool exchange needs an operator at the tool.
5. Provenance and status
[0024]This document is an original combination composed from a typed library of mechanism blocks. Each block was derived from a published patent and carries typed connection points, the parameters its source states, and its own construction and operating description. The combination described here is proposed and has not been constructed. The published documents behind the blocks used in this arrangement are EP-4489564-B1, US-11427405-B1, US-11858125-B2, US-2022339798-A1, US-8132312-B2; their text is not reproduced, and the description above is generated from the structure of the combination.