OPENTECHNICAL PUBLICATION OT-2026-000033187 Three cup vacuum gripper, three zone face, six outlet manifold, plant vacuum fed, pulsed blow-off before set-down Published: 2026-09-17T08:21:57.065765Z Permanent URL: https://opentechnical.org/p/OT-2026-000033187 Categories: Robotics & Automation > End Effectors > Vacuum Grippers ------------------------------------------------------------------------ ABSTRACT A zoned vacuum gripping tool comprising one mounting flange, three suction cups, one plant vacuum connection, one manifold, three zone branches, one contact detector and one blow-off valve. When the suction cups reach the workpiece, the suction cups are evacuated by the plant vacuum connection. Before the workpiece reaches the set-down position, the workpiece is blown off by the blow-off valve while the workpiece is above the receiving surface. The arrangement is a proposed configuration composed from a typed library of mechanism blocks derived from published patents; it has not been constructed. 1. Purpose and arrangement [0001] This disclosure describes a zoned vacuum gripping tool: three suction cups carried on a mounting flange, fed by a plant vacuum connection. It is arranged for handling workpieces that do not cover the whole gripping face, starting the cycle at the moment of contact and clearing the face at release. One concrete embodiment is described; every connection is stated with the medium it carries, and the operating sequence is given as conditions on named operations. 2. Components, construction and connections [0002] One mounting flange. The mounting flange carries the whole assembly and presents the bolt pattern that meets the robot. [0003] Three suction cups. Each suction cup presents a sealing lip to the workpiece and is evacuated through its own connection. The count of three follows from the arrangement: one gripping element per zone branch. The suction cups are of the flat form. [0004] One plant vacuum connection. The plant vacuum connection takes vacuum from the plant line, so the tool carries no generator of its own. [0005] One manifold. The manifold receives the vacuum at one inlet and distributes it to its outlets. The manifold has six outlets. [0006] Three zone branches. Each zone branch carries the vacuum of one zone of the face and no other. The count of three follows from the arrangement: one branch per zone. The distribution is divided into three zones, each fed by its own branch. [0007] One contact detector. The contact detector reports the moment a workpiece is present at the gripping face; its sensing technology is not fixed by this arrangement. The contact detector is mounted on the frame. [0008] One blow-off valve. The blow-off valve drives compressed air back through the circuit to the face, which clears the face instead of waiting for the circuit to refill. The blow-off is a short pulse. The blow-off pulse is given before set-down. [0009] The suction cups are carried on the tool side of the mounting flange. [0010] The manifold is fixed to the tool side of the mounting flange. [0011] The manifold inlet is connected to the plant vacuum connection, which supplies every outlet of the manifold. [0012] Each of the three zone branches is taken from its own manifold outlet, so that the branch carries the vacuum of its own zone only. [0013] Each suction cup is connected to its own zone line, one suction cup per zone, and is evacuated through that line. [0014] The contact detector is mounted on the frame and reports the moment a workpiece is present against the gripping face. [0015] The blow-off valve is connected to the circuit at the plant vacuum connection, so that compressed air can be driven back through the circuit to the face. [0016] The robot side of the mounting flange is bolted to the robot flange. [0017] The remaining three manifold outlets are plugged and carry no line. [0018] The blow-off valve is fed from the compressed air supply of the cell. [0019] The blow-off valve is switched by the cell controller; the contact detector reports to the cell controller. 3. Operating sequence and conditions [0020] - After the contact detector has detected the workpiece, the vacuum supply is actuated by the cell controller. [0021] - When the suction cups reach the workpiece, the suction cups are evacuated by the plant vacuum connection. [0022] - Before the workpiece reaches the set-down position, the workpiece is blown off by the blow-off valve while the workpiece is above the receiving surface. [0023] - The workpiece is held until the blow-off valve has opened the circuit. [0024] The cell controller reads the contact detector (on the frame) and commands the blow-off valve; no sensor drives an actuator directly. 4. Parameters and operating assumptions [0025] Parameter values of this embodiment: form of the suction cups: flat (sets the shape of the contact area and the behaviour of the lip on a curved workpiece); material of the suction cups: polyurethane (sets the friction at the lip and the tolerance of the lip to oil and heat); outlets of the manifold: six (sets how many lines can be fed from one inlet); material of the zone branches: plastic; zones of the zone branches: three (sets how much of the face can be treated separately); placement of the contact detector: on the frame (sets where the presence of the workpiece is detected); duration of the blow-off valve: a short pulse (sets how quickly the face clears and how much air each release costs); timing of the blow-off valve: before set-down (sets whether the pulse assists a drop release or clears the face after set-down). [0026] The workpiece is released while it is still above the receiving surface and falls the remaining distance onto it. This sequence is for a workpiece and a receiving surface that tolerate that drop, for example a part released into a container or onto a conveyor; the drop height is set by the application and is not fixed here. [0027] The blow-off is a short pulse: the valve opens for a fraction of a second, long enough to break the seal and clear the face, and closes again. [0028] The tool carries no valve between the plant line and the face, so the plant vacuum is applied to the face whenever the plant line is live; release relies on the release element alone. 5. Provenance and status [0029] This document is an original combination composed from a typed library of mechanism blocks. Each block was derived from a published patent and carries typed connection points, the parameters its source states, and its own construction and operating description. The combination described here is proposed and has not been constructed. The published documents behind the blocks used in this arrangement are US-10259123-B2, US-10549431-B2, US-2016214812-A1, US-2022339798-A1, US-8006968-B2, US-8132312-B2, WO-2026020244-A1; their text is not reproduced, and the description above is generated from the structure of the combination. ------------------------------------------------------------------------ OpenTechnical publication OT-2026-000033187 Published 2026-09-17T08:21:57.065765Z https://opentechnical.org/p/OT-2026-000033187