OPENTECHNICAL PUBLICATION OT-2026-000050894 Two pad foam vacuum gripper, two outlet manifold, single stage ejector, vented before set-down Published: 2026-09-17T08:36:41.548889Z Permanent URL: https://opentechnical.org/p/OT-2026-000050894 Categories: Robotics & Automation > End Effectors > Vacuum Grippers ------------------------------------------------------------------------ ABSTRACT A foam-pad vacuum gripping tool comprising one mounting flange, two foam pads, one ejector, one manifold and one vent valve. When the foam pads reach the workpiece, the foam pads are evacuated by the ejector. Before the workpiece reaches the set-down position, the vacuum circuit is vented by the vent valve while the workpiece is above the receiving surface. The arrangement is a proposed configuration composed from a typed library of mechanism blocks derived from published patents; it has not been constructed. 1. Purpose and arrangement [0001] This disclosure describes a foam-pad vacuum gripping tool: two foam pads carried on a mounting flange, fed by an ejector. It is arranged for controlling the moment of release and holding a workpiece that a rigid lip cannot seal against. One concrete embodiment is described; every connection is stated with the medium it carries, and the operating sequence is given as conditions on named operations. 2. Components, construction and connections [0002] One mounting flange. The mounting flange carries the whole assembly and presents the bolt pattern that meets the robot. [0003] Two foam pads. Each foam pad presents a compliant face to the workpiece; the holding force is spread over the contact area rather than concentrated at a lip. The count of two follows from the arrangement: one gripping element per manifold outlet. The pad is of closed cell foam. [0004] One ejector. The ejector draws the circuit down by passing compressed air through a nozzle; it has no moving part at the tool and consumes air for as long as it runs. The ejector has one stage. [0005] One manifold. The manifold receives the vacuum at one inlet and distributes it to its outlets. The manifold has two outlets. [0006] One vent valve. The vent valve opens the circuit it is connected to towards atmosphere, which ends the grip. The circuit is vented before set-down. [0007] The foam pads are carried on the tool side of the mounting flange. [0008] The manifold is fixed to the tool side of the mounting flange. [0009] The ejector is fixed to the tool side of the mounting flange. [0010] The manifold inlet is connected to the ejector outlet, which supplies every outlet of the manifold. [0011] Each manifold outlet feeds one foam pad by its own vacuum line, so that the two outlets feed two foam pads. [0012] The vent valve is connected to the circuit at the ejector outlet and opens that circuit to atmosphere when it is actuated. [0013] The robot side of the mounting flange is bolted to the robot flange. [0014] The ejector is fed from the compressed air supply of the cell. [0015] The vent valve is switched by the cell controller. 3. Operating sequence and conditions [0016] - When the foam pads reach the workpiece, the foam pads are evacuated by the ejector. [0017] - Before the workpiece reaches the set-down position, the vacuum circuit is vented by the vent valve while the workpiece is above the receiving surface. [0018] - The workpiece is held until the vent valve has opened the circuit. [0019] The cell controller commands the vent valve; no sensor drives an actuator directly. 4. Parameters and operating assumptions [0020] Parameter values of this embodiment: material of the foam pads: sponge (sets the compliance of the sealing face); porosity of the foam pads: closed cell (sets whether air passes through the pad body or only through openings cut through it); stages of the ejector: one (sets the flow drawn at low vacuum and the compressed air consumed while a sealed face is held); outlets of the manifold: two (sets how many lines can be fed from one inlet); timing of the vent valve: before set-down (sets whether the workpiece is released before or after it is supported by the set-down surface). [0021] The workpiece is released while it is still above the receiving surface and falls the remaining distance onto it. This sequence is for a workpiece and a receiving surface that tolerate that drop, for example a part released into a container or onto a conveyor; the drop height is set by the application and is not fixed here. [0022] The closed-cell foam does not pass air through its body; the face is evacuated through openings cut through the pad into the distribution chamber, and the foam around each opening forms the seal against the workpiece. 5. Provenance and status [0023] This document is an original combination composed from a typed library of mechanism blocks. Each block was derived from a published patent and carries typed connection points, the parameters its source states, and its own construction and operating description. The combination described here is proposed and has not been constructed. The published documents behind the blocks used in this arrangement are EP-4385681-B1, US-10549431-B2, US-8006968-B2, WO-2008134339-A4; their text is not reproduced, and the description above is generated from the structure of the combination. ------------------------------------------------------------------------ OpenTechnical publication OT-2026-000050894 Published 2026-09-17T08:36:41.548889Z https://opentechnical.org/p/OT-2026-000050894