OPENTECHNICAL PUBLICATION OT-2026-000053318 Three pad foam vacuum gripper, three outlet manifold, pump fed, vented before set-down, on a tool changer Published: 2026-09-17T08:39:09.762364Z Permanent URL: https://opentechnical.org/p/OT-2026-000053318 Categories: Robotics & Automation > End Effectors > Vacuum Grippers ------------------------------------------------------------------------ ABSTRACT A foam-pad vacuum gripping tool comprising one tool-change interface, three foam pads, one vacuum pump, one manifold, one contact detector and one vent valve. When the foam pads reach the workpiece, the foam pads are evacuated by the vacuum pump. Before the workpiece reaches the set-down position, the vacuum circuit is vented by the vent valve while the workpiece is above the receiving surface. The arrangement is a proposed configuration composed from a typed library of mechanism blocks derived from published patents; it has not been constructed. 1. Purpose and arrangement [0001] This disclosure describes a foam-pad vacuum gripping tool: three foam pads carried on a tool-change interface, fed by a vacuum pump. It is arranged for starting the cycle at the moment of contact, controlling the moment of release, holding a workpiece that a rigid lip cannot seal against and exchanging the tool without rewiring the cell. One concrete embodiment is described; every connection is stated with the medium it carries, and the operating sequence is given as conditions on named operations. 2. Components, construction and connections [0002] One tool-change interface. The tool-change interface splits the tool into a robot side and a tool side, so the tool can be exchanged without dismantling it. The tool-change interface has a mechanical lock. [0003] Three foam pads. Each foam pad presents a compliant face to the workpiece; the holding force is spread over the contact area rather than concentrated at a lip. The count of three follows from the arrangement: one gripping element per manifold outlet. The pad is of open cell foam. [0004] One vacuum pump. The pump draws the circuit down mechanically and adds its own mass to the moving assembly. [0005] One manifold. The manifold receives the vacuum at one inlet and distributes it to its outlets. The manifold has three outlets. [0006] One contact detector. The contact detector reports the moment a workpiece is present at the gripping face; its sensing technology is not fixed by this arrangement. The contact detector is mounted on the frame. [0007] One vent valve. The vent valve opens the circuit it is connected to towards atmosphere, which ends the grip. The circuit is vented before set-down. [0008] The foam pads are carried on the tool side of the tool-change interface. [0009] The manifold is fixed to the tool side of the tool-change interface. [0010] The vacuum pump is fixed to the tool side of the tool-change interface. [0011] The manifold inlet is connected to the pump inlet line, which supplies every outlet of the manifold. [0012] Each manifold outlet feeds one foam pad by its own vacuum line, so that the three outlets feed three foam pads. [0013] The contact detector is mounted on the frame and reports the moment a workpiece is present against the gripping face. [0014] The vent valve is connected to the circuit at the pump inlet line and opens that circuit to atmosphere when it is actuated. [0015] The robot side of the tool-change interface is bolted to the robot flange. [0016] The pump motor is supplied from the electrical supply of the cell. [0017] The vent valve is switched by the cell controller; the contact detector reports to the cell controller. 3. Operating sequence and conditions [0018] - After the contact detector has detected the workpiece, the vacuum supply is actuated by the cell controller. [0019] - When the foam pads reach the workpiece, the foam pads are evacuated by the vacuum pump. [0020] - Before the workpiece reaches the set-down position, the vacuum circuit is vented by the vent valve while the workpiece is above the receiving surface. [0021] - The workpiece is held until the vent valve has opened the circuit. [0022] The cell controller reads the contact detector (on the frame) and commands the vent valve; no sensor drives an actuator directly. 4. Parameters and operating assumptions [0023] Parameter values of this embodiment: locking of the tool-change interface: mechanical (sets what has to be present at the interface for the tool to stay attached); material of the foam pads: sponge (sets the compliance of the sealing face); porosity of the foam pads: open cell (sets whether air passes through the pad body or only through openings cut through it); drive medium of the vacuum pump: electric (sets the supply the pump motor needs from the cell); outlets of the manifold: three (sets how many lines can be fed from one inlet); placement of the contact detector: on the frame (sets where the presence of the workpiece is detected); timing of the vent valve: before set-down (sets whether the workpiece is released before or after it is supported by the set-down surface). [0024] The workpiece is released while it is still above the receiving surface and falls the remaining distance onto it. This sequence is for a workpiece and a receiving surface that tolerate that drop, for example a part released into a container or onto a conveyor; the drop height is set by the application and is not fixed here. [0025] The open-cell foam passes air through its whole face, so an uncovered part of the face draws air through the pad itself; the supply is sized for that continuous flow and the pad relies on flow restriction through the foam, not on a seal, to hold vacuum behind a covered area. [0026] The lock is engaged by a manually operated lever on the interface; no supply crosses the interface for the lock, and tool exchange needs an operator at the tool. 5. Provenance and status [0027] This document is an original combination composed from a typed library of mechanism blocks. Each block was derived from a published patent and carries typed connection points, the parameters its source states, and its own construction and operating description. The combination described here is proposed and has not been constructed. The published documents behind the blocks used in this arrangement are EP-4385681-B1, US-11427405-B1, US-11858125-B2, US-2022339798-A1, US-8006968-B2, WO-2008134339-A4; their text is not reproduced, and the description above is generated from the structure of the combination. ------------------------------------------------------------------------ OpenTechnical publication OT-2026-000053318 Published 2026-09-17T08:39:09.762364Z https://opentechnical.org/p/OT-2026-000053318